flat assembler
Message board for the users of flat assembler.
Index
> DOS > convert mantissa bits to decimal fraction number 
Author 

smiddy
I have yet to crack that nut, since I am not working on it yet. I will when I write the calculator for my OS. Take a look at this and see if this gives you some ideas: http://www.x86asm.net/articles/workingwithbignumbersusingx86instructions/


05 Jun 2015, 02:53 

mns
thanks smiddy.i think it will give a idea for the problem(though i have lot to understand)
Last edited by mns on 05 Jun 2015, 11:56; edited 1 time in total 

05 Jun 2015, 05:56 

revolution
The basic idea is to multiply by some power of 10 to get the required number of digits precision.
For example your binary number 01011110101110000101001 (which is 0.37000000476837158203125) can be converted to 4 digits of precision by multiplying by 10^4 and dividing by 2^23. (0x2F5C29 * 10000) shr 23 = 3700. 

05 Jun 2015, 06:10 

mns
thank you revolution.but i want to convert all 23 bits of mantissa field to decimal number and display it(using assembly code).i think my actual problem is, dealing with large numbers in assembly.


05 Jun 2015, 12:45 

revolution
23 bits doesn't need any special coding. If you want a full 7 digits precision then you can do this:
Code: mov eax,0x2F5C29 shl (3223) ;move to high order bits mov edx,10000000 mul edx ;edx = 3700000 

05 Jun 2015, 12:51 

revolution
I should probably add that you can keep extracting more more digits by continuing the code:
Code: mov eax,0x2F5C29 shl (3223) ;move to high order bits mov ecx,1000000000 ;get 9 digits per pass mul ecx ;edx = 370000004 ;<print first 9 digits> mul ecx ;edx = 768371582 ;<print next 9 digits> mul ecx ;edx = 031250000 ;<print next 9 digits> etc. 

05 Jun 2015, 14:34 

mns
thank you revolution.your solution works fine.but still i'm trying to figure out how it works and what is the math behind it.I'm grateful if you can explain more.


05 Jun 2015, 19:26 

revolution
The premise is that the binary number is implied to be 0.xxxx... That is, the number is [0,1). Only 23bits are given but it is assumed that other trailing bits are all zeros.
After each mul instruction the values to the left of the binary point are printed and then discarded, and the values to the right of the binary point are kept for the next iteration. After mul it looks like this: yyyy.xxxx... Then yyyy is printed and the remaining 0.xxxx... is run through again. 

06 Jun 2015, 15:30 

mns
thanks.but how these bits interpreted as fraction numbers(0.xxxx) and not integers(xxxx) with your code.in other words, what is the mathematical equation your code based on?
sorry for bothering you so much.(i think i have a long way to go to understand even basic things in assembly). 

06 Jun 2015, 18:44 

revolution
EAX contains the xxxx part and the binary point is at bit 32. After the MUL instruction EDX contains the yyyy part and EAX contains the next xxxx part. This is essentially a fixed point representation of 32.32.


07 Jun 2015, 01:19 

mns
thanks again revolution.i got the idea.
it is like, let's say binary fraction .1101  if it is a complete number it would be (1101) = 13 in decimal as it is a binary fraction it is = 13/16 in decimal which is 13/2^4 which is (1x2^(41))+(1x2^(42))+(0x2^(43))+(1x2^(44))/2^4 like that .01011110101110000101001 in decimal is, ((1or0)x2^(231))+((1or0)x2^(232))+((1or0)x2^(233))+((1or0)x2^(234))+........./2^23 when shl (3223) it will be, ((1or0)x2^(321))+((1or0)x2^(322))+((1or0)x2^(323))+((1or0)x2^(324))+........./2^32 when mul, actual division by 2^32 take place and and the result will be at edx.(i hope i'm correct in this ) 

07 Jun 2015, 04:46 

El Tangas
Yes, that's it. If you want to convert it to a string for printing, you can multiply just by 10 so that you only extract one decimal digit at a time. The remainder will be left in EAX, repeat until EAX is zero (or until you are satisfied with the decimal precision for display). EAX will always eventually reach zero, because any finite lenght binary fraction can be represented by a finite lenght decimal fraction (in fact they will have the same number of digits). Can take a while, though...
For printing, add each result in EDX to '0' char and build the string. 

07 Jun 2015, 23:36 

mns
good,
thank you very much El Tangas and revolution for you kind help. 

08 Jun 2015, 03:55 

El Tangas
Just one more thing, in case you want to convert an ieee float to decimal to print in scientific notation, some adjustments have to be made to the binary mantissa and exponent beforehand.
1) Exponent multiply the binary exponent by the constant log_10(2) that you can for exemple load in the x87 fpu with the fldlg2 instruction. This is an important constant for these conversions, that's why it's hardcoded in the fpu. Take the integer part of the result as the decimal exponent. Then calculate 10^(remainder) for the next step. 2) Mantissa Take the binary mantissa and multiply by 10^(remainder) calculated before, to obtain the decimal mantissa. You will notice (using log and exponent properties) that these operations actually don't change the number, just adjust from M*2^a to N*10^b forms. Once you have the adjusted exponent and mantissa, you can convert to decimal using the techniques shown before. 

08 Jun 2015, 09:50 

revolution
El Tangas wrote: Just one more thing, in case you want to convert an ieee float to decimal to print in scientific notation, some adjustments have to be made to the binary mantissa and exponent beforehand. 

08 Jun 2015, 11:26 

redsock
FWIW, this is a good read, and how I implemented it in my own library: http://www.cs.indiana.edu/~dyb/pubs/FPPrintingPLDI96.pdf


08 Jun 2015, 22:16 

mns
again thank you all for your invaluable replies.


10 Jun 2015, 11:36 

< Last Thread  Next Thread > 
Forum Rules:

Copyright © 19992020, Tomasz Grysztar. Also on YouTube, Twitter.
Website powered by rwasa.