flat assembler
Message board for the users of flat assembler.
![]() Goto page 1, 2 Next |
Author |
|
MHajduk
I have got an old (produced in Malaysia in 80's or 90's) but still functional electronic calculator, Citizen SDC-848. It is said to be powered from two sources: solar panel and battery but in fact it works well only in properly illuminated places.
I'd like to know what kind of batteries are used in this type of calculator. In the Internet I can find only incomplete or contradictory information. Some sources claim that this calculator was powered only from the solar panel despite of the description on the cover: "2 POWER". Datasheet from an internet museum of calculators: http://mycalcdb.free.fr/main.php?l=0&id=6824 |
|||
![]() |
|
revolution
Open it up and post a picture of the battery(s).
|
|||
![]() |
|
MHajduk
Thanks for your replies revolution and shoorick.
I have opened it up for the first time and have taken the photo presented below: ![]() and yes, I am aware that the cost of the battery can be comparable with the cost of a new calculator. ![]() |
|||
![]() |
|
DimonSoft
MHajduk wrote: Thanks for your replies revolution and shoorick. The text written on the battery seems to give a lot of search results, even with Amazon pages. I wonder if this one is replaceable with the one used in desktops. |
|||
![]() |
|
MHajduk
I have made some searches too and found alternatives that are really cheap. However, to make the cost of delivery of the parcel lower than the cost of delivered items I have to combine it with sets of accumulators (for a digital camera etc.) that I'm going to order anyway.
![]() |
|||
![]() |
|
revolution
It is difficult to know the scale but perhaps that is an LR44 size button cell.
|
|||
![]() |
|
MHajduk
revolution wrote: It is difficult to know the scale but perhaps that is an LR44 size button cell. The same sources also give the information that analogues for LR44 are G13 and A76. I'm not an expert in that matter and have got also another Citizen calculator SRP-45 (produced in Thailand in 90's) that needs two A76 batteries, so I most probably will buy two blisters containing pairs of LR54 and LR44 respectively. ![]() |
|||
![]() |
|
revolution
BTW: When the battery holder was soldered in, they forgot to clean up the flux residue (that is the brown stuff around the solder pads). The flux can be quite acidic. You might want to consider cleaning it off before it eats through the board. Products of the type "contact cleaners" usually are good for clearing that stuff away.
|
|||
![]() |
|
MHajduk
revolution wrote: BTW: When the battery holder was soldered in, they forgot to clean up the flux residue (that is the brown stuff around the solder pads). The flux can be quite acidic. You might want to consider cleaning it off before it eats through the board. Products of the type "contact cleaners" usually are good for clearing that stuff away. |
|||
![]() |
|
revolution
Yes. If you have some rubbing alcohol, or IPA, or similar, then you can try that also.
|
|||
![]() |
|
MHajduk
Here you have photos of the same battery with the scale added:
in centimeters ![]() in inches ![]() |
|||
![]() |
|
revolution
11.6mm diameter is either LR44 or LR54. The LR44 is 5.4mm high. The LR54 is 3.1mm high.
You can also use SR instead of LR. |
|||
![]() |
|
MHajduk
revolution wrote: 11.6mm diameter is either LR44 or LR54. The LR44 is 5.4mm high. The LR54 is 3.1mm high. ![]() Detailed view: ![]() |
|||
![]() |
|
revolution
I hope that vernier is not metal.
![]() Yeah, it appears as though you have LR54 or SR54. |
|||
![]() |
|
revolution
So talking about shorting out those batteries with metallic verniers. Another thing to be careful of when you install the new one is to make sure you don't touch it with your fingers. The oils in the skin can create a bridge across the terminals and drain the battery within a few months. Wear some clean gloves, or use some plastic tweezers, or both, when handling the batteries.
|
|||
![]() |
|
MHajduk
revolution wrote: So talking about shorting out those batteries with metallic verniers. Another thing to be careful of when you install the new one is to make sure you don't touch it with your fingers. The oils in the skin can create a bridge across the terminals and drain the battery within a few months. Wear some clean gloves, or use some plastic tweezers, or both, when handling the batteries. ![]() |
|||
![]() |
|
revolution
You can get really cheap plastic vernier calipers. They aren't very accurate IME, but good enough for general usage if one isn't doing finely detailed work, and understands there are probably relatively big errors.
|
|||
![]() |
|
MHajduk
revolution wrote: You can get really cheap plastic vernier calipers. They aren't very accurate IME, but good enough for general usage if one isn't doing finely detailed work, and understands there are probably relatively big errors. |
|||
![]() |
|
shoorick
using metal caliper you can measure battery insulated with thin polyethilen, obviously it may be piece of packing bag or similar
|
|||
![]() |
|
Goto page 1, 2 Next < Last Thread | Next Thread > |
Forum Rules:
|
Copyright © 1999-2019, Tomasz Grysztar.
Powered by rwasa.